CGDI FC200 Update: Citroën/Peugeot MEVD17.4.2 & BMW FSC Repair

The CGDI FC200 V1.4.1.2 update adds ECU data read/write support for more vehicle systems, FSC-related fault repair for locked BMW MD1/MG1 ECUs, BMW VIN modification, and Great Wall mileage repair. It also fixes several communication, data parsing, and reading issues while optimizing existing ECU and mileage repair functions.


What's New

1. Added ECU Data Read/Write Support

Domestic Vehicles: MT22.1.1 MC9S12XEQ384 (Bench)

Citroën / Peugeot: MEVD17.4.2 (Boot)

Dongfeng: ME7.4.4 (Boot)


2. Added BMW MD1/MG1 FSC-Related Fault Repair

Supports repairing FSC-related faults on locked Bosch MD1/MG1 series ECUs after data read/write operations.


3. Added VIN Modification

BMW: MSV80 / MSV80.1


4. Added Mileage Repair

Great Wall: EDC17C53


5. Fixed Issues

Fixed T93 transmission communication issues.

Fixed data parsing failures when uploading MED17.4 data for DTC off.

Fixed data parsing failures when performing DTC off on Mercedes-Benz MD1CP001.

Fixed DTC parsing failures on Volkswagen MED17.5.5.

Fixed the issue preventing data reading from the Wuling FC-34.


6. Optimized Existing Functions

Improved connectivity after unlocking MD1/MG1 series ECUs.

Optimized data reading for the Nissan EFI SH72531 system.

Improved mileage repair for ME17.5.22.

Optimized T87A identification and data reading.

Fixed the issue where CALID remained unavailable after repair on domestic ME17.8.8 ECUs.


Applicable Platforms

This update applies to the CGDI FC200 ECU Programmer.


More updates are coming soon.

cgdi-fc200-update-citroen-peugeot-mevd17-4-2-bmw-fsc-repair

www.obd2shop.co.uk


Comments

Post a Comment

Popular posts from this blog

W164 2009 +/W221 2009+ All Key lost with CGDI MB in 10 minutes

Image
In the past: CGDI MB collected data from EIS when W164 2009 +/W221 2009+ All Key lost, it cost about 2 hours.  Here a user's experience, if you had the same experience, you can skip to the next part. I did it today (EIS on the bench) w164 eis A1645451508 new type pulling dump took 80 minutes calculating pass online 4 min. key programmed !!! w164 after 2009 I did for testing 2 types of programming _ have got EZS with both programmed keys because customer claimed sometimes EIS works sometimes doesn't - I have found that connector for immo aerial was desoldered from PCB so when I fixed it - EIS became fully working again - and then I started testing CGDI and made 2 types of programming (all programming on bench - EZS + GATEWAY EMULATOR) 1) programming in case one key is available and adding spare key - ALL OK! 2) programming in case of ALL KEYS LOST - ALL OK! spare key programming was pretty fast AKL scenario takes circa 80minutes to get data from EIS and You hav...
Read more

CG100X Software Download, installation and activation

Image
This post will guide you on how to download, install, and activate the software of the CGDI CG100X programmer . CG100X Software Download: https://mega.nz/folder/3CIXXDJC#jJ4CdJ9T-eEYhkBYi6Z65A Click the link above to open the CG100X folder and download it to your computer. CG100X Software installation and activation: Connect CG100X to the computer with a USB cable, and then open the software installed on the computer. Follow the prompts and select "Install" to complete the software installation. Open "CG100X, it "prompts" "The device is not active, can not be used." "Before activation, please log in to your account and bind your device." Click "OK" to continue. It comes to the current interface and selects "No account? Create one!" Fill in the following information and click "Next". Choose one of the following two methods for verification. Here we use email verification. Click "Get verification code"....
Read more

CGDI Prog MB key programmer software V2.8.0.0 download

Image
Good news!!  CGDI Prog MB key programmer software can be updated to Version 2.8.0.0. Please keep reading to find out the download link and more info. CGDI Prog MB V2.8.0.0 download: http://www.cgprogcar.com/en/?c=list&cs=xiazaizhongxin CGDI Prog MB  V2.8.0.0  update content:  update time: 2018.10.28 1. Added online store function Now, you can self-renew your password calculation service or recharge points in the store. Currently, only WeChat payment is supported. 2. Added the automatic activation function When you first purchase a device, you can choose the subscription service version to activate the device. Please note that the subscription version cannot be changed after activation. 3. Remove the limit on the number of password calculations per day   You can calculate the password as much as possible within a day. Of course, the premise is that you have more than enough points. 4. We greatly optimized the stability o...
Read more